Product classification: trapezoidal tooth rubber synchronous belt -T2.5 synchronous belt series．
Product synopsis: layer rubber trapezoidal tooth synchronous belt of the belt is manufactured quality neoprene raw materials imported from Japan, skeleton layer is high quality glass fiber cord is imported from Japan, adopting high tooth surface wear-resisting layer adopts nylon 66 / do protection. The products have the characteristics of dynamic flexion, good anti-cracking, good ozone performance, aging resistance, heat resistance, oil resistance and wear resistance. Trapezoidal tooth synchronous belt models include: MXL, XL, L, H, XH, XH, XXH, T2.5, T5, T10, T20, AT5, AT10, AT20, etc.
1,It is strictly forbidden to break the T2.5 synchronously, bend it, avoid the damage of the powerful layer, and lose the value of use.
2,The T2.5 synchronous belt should not be kept in an abnormal bending state.
3,Keep the T2.5 synchronous belt in the shade to avoid direct sunlight, so the synchronous belt will age easily.
4,During installation, please shorten the center distance, relax the tension wheel, and not force the belt to be loaded from the bottom of the belt wheel.
5,The tooth of the T2.5 synchronous belt wheel must be at a right Angle to the running direction.
6,The parallel degree of the main axis of the active wheel and the passive wheel is controlled at the tangent = 1/1000. No axial position can directly affect the service life.
7,It is found that the T2.5 synchronous belt on the active wheel is deflated to one side. It should move the passive wheel to adjust and adjust the pressure of the tensioning wheel.
8,At the start, the center is changed, the T2.5 synchronous belt loosens, and the jumping tooth phenomenon should be checked if the wheel frame is loose, and the positioning of the shaft is inaccurate. Adjust and reinforce.
9,T2.5 synchronous belt installation must be properly tensioning with different models and bandwidths.
10,The tensioning wheel must be mounted on the side of the driving loose side.
The synchronous belt drive is a new belt drive which combines the advantages of belt drive, chain drive and gear transmission. Due to work like tooth shape, tooth of the pulley meshing transmission, and by the load on the tensile layer, to maintain with constant pitch line length, so there is no relative sliding between band and pulley, so that the main, driven wheel can do no slip between synchronous transmission. The speed range of synchronous belt transmission ranges from several revolutions per minute to the linear speed of 40m/s, the speed ratio can reach 10, the transmission efficiency can reach 99%, and the transmission power can range from a few watts to hundreds of watts. In recent years, mining, metallurgy, iron and steel machinery, medical equipment demand increasing, synchronous belt transmission is now in a variety of instruments, computer, sewing machines, textile machines, chemical fiber machine, and other widely used in general machinery.

specification	Section line length	Tooth number
T2.5×145	145.00	58
T2.5×157.5	157.50	63
T2.5×160	160.00	64
T2.5×172.5	172.50	69
T2.5×177.5	177.50	71
T2.5×185	185.00	74
T2.5×200	200.00	80
T2.5×230	230.00	92
T2.5×245	245.00	98
T2.5×265	265.00	106
T2.5×272.5	272.50	109
T2.5×275	275.00	110
T2.5×280	280.00	112
T2.5×285	285.00	114
T2.5×300	300.00	120
T2.5×305	305.00	122
T2.5×330	330.00	132
T2.5×335	335.00	134
T2.5×355	355.00	142
T2.5×380	380.00	152
T2.5×420	420.00	168
T2.5×450	450.00	180
T2.5×480	480.00	192
T2.5×500	500.00	200
T2.5×512.5	512.50	205
T2.5×580	580.00	232
T2.5×620	620.00	248
T2.5×625	625.00	250
T2.5×690	690.00	276
T2.5×780	780.00	312
T2.5×860	860.00	344