Product classification: trapezoidal double-sided teeth synchronous belt -DAT10 synchronous belt series
Product description: rubber trapezoid double layer tooth synchronous belt of the belt is manufactured quality neoprene raw materials imported from Japan, skeleton layer is high quality glass fiber cord is imported from Japan, adopting high tooth surface wear-resisting layer adopts nylon 66 / do protection. In addition, the polyurethane is the double-sided tape of the material. The products have the characteristics of dynamic flexion, good anti-cracking, good ozone performance, aging resistance, heat resistance, oil resistance and wear resistance. The model of trapezoid double-sided synchronous belt includes: XL, L, H, XH, XH, XXH, T2.5, T5, T10, T20, AT5, AT10, AT20, etc.
1、It is strictly forbidden to overbreak, bend, avoid strong layer damage and lose use value.
2、The DAT10 double tooth synchronous belt should not be kept in an abnormal bending state.
3、Keep the DAT10 double synchronous belt in the shade.
4、When installing, please shorten the center distance and relax the tensioning wheel. It is not allowed to force drag and drag from the bottom of the belt wheel.
5、The teeth of the DAT10 synchronous belt wheel must be at a right Angle to the running direction.
6、The parallel degree of the main axis of the active wheel and the passive wheel is controlled at the tangent = 1/1000. No axial position can directly affect the service life.
7、Find out that the DAT10 double-sided gear on the active wheel is sideways to one side, the passive wheel should be adjusted and the pressure of the tension wheel should be adjusted.
8、At the start, the center distance is changed, the DAT10 double tooth synchronous belt relaxation, the occurrence of jumping tooth phenomenon, should check whether the belt wheel frame is loose, and the positioning of the shaft is inaccurate. Adjust and reinforce.
9、The DAT10 double tooth synchronous belt installation must be properly tensioning with different models and bandwidths.
10、The tensioning wheel must be mounted on the side of the driving loose side.
The tensioning wheel must be mounted on the side of the driving loose side. Synchronous belt transmission is a new belt transmission which combines the advantages of belt drive, chain drive and gear transmission. Due to work like tooth shape, tooth of the pulley meshing transmission, and by the load on the tensile layer, to maintain with constant pitch line length, so there is no relative sliding between band and pulley, so that the main, driven wheel can do no slip between synchronous transmission. The speed range of synchronous belt transmission ranges from several revolutions per minute to the linear speed of 40m/s, the speed ratio can reach 10, the transmission efficiency can reach 99%, and the transmission power can range from a few watts to hundreds of watts. In recent years, mining metallurgy, iron and steel, machinery, medical equipment, the increasing demand, synchronous belt transmission is now in a variety of instruments, computer, sewing machines, textile machines, chemical fiber is widely used in machine, and other general machinery.
|
specification
|
Section line length(mm)
|
Number of teeth
|
|
AT10X500
|
500.00
|
50
|
|
AT10X560
|
560.00
|
56
|
|
AT10X580
|
580.00
|
58
|
|
AT10X660
|
660.00
|
66
|
|
AT10X730
|
730.00
|
73
|
|
AT10X840
|
840.00
|
84
|
|
AT10X920
|
920.00
|
92
|
|
AT10X960
|
960.00
|
96
|
|
AT10X1010
|
1010.00
|
101
|
|
AT10X1150
|
1150.00
|
115
|
|
AT10X1210
|
1210.00
|
121
|
|
AT10X1240
|
1240.00
|
124
|
|
AT10X1250
|
1250.00
|
125
|
|
AT10X1280
|
1280.00
|
128
|
|
AT10X1320
|
1320.00
|
132
|
|
AT10X1500
|
1500.00
|
150
|
|
AT10X1610
|
1610.00
|
161
|
|
AT10X1800
|
1800.00
|
180
|
|
AT10X1940
|
1940.00
|
194
|
|
AT10X2000
|
2000.00
|
200
|
|
AT10X2250
|
2250.00
|
225
|
|
AT10X2590
|
2590.00
|
259
|
|
AT10X2880
|
2880.00
|
288
|
|
AT10X3080
|
3080.00
|
308
|
|
AT10X3150
|
3150.00
|
315
|
|
AT10X3340
|
3340.00
|
334
|
|
AT10X4030
|
4030.00
|
403
|
